Lyman TargetSpot and Jr. Targetspot scope caps

Available in traditional Black.  Red discontinued sorry, Gold limited availability as of Aug. 2025.

- TS caps top row - JTS caps bottom row.

- Anodized aluminum.

- Sold as the set only.

- $27.90 per set for TS, plus shipping.

- $24.20 per set for JTS, plus shipping.

Lyman Super TargetSpot scope caps

Available in traditional Black.  Red discontinued sorry, Gold limited availability as of Aug. 2025.

- Anodized aluminum.

- Sold as the set only.

- $30.30 per set, plus shipping.

Lyman Super TargetSpot sunshades

- Black anodized aluminum.

- 2.5", 4" (standing up), and 6".

- $66.00, $79.20, and $91.30 respectively, plus shipping.

- These will accept the standard scope cap at the far end.   So you could stack them...

Note for scope caps below, where measurements are shown...

    - Scope designated sizes (1-1/2", 1", etc.) are NOT the outside diameter of the objective.

    - Scope sizes are usually the clear thru-the-lens diameter. So a named 1-1/4" scope may measure 1-1/2" outside diameter, which causes understandable confusion.

    - Measurements shown are the outside diameter of the cap threads.

    - The inside (female) thread of the scope will measure about .020" smaller.

    - Objective cap outside diameters may be 1/8" to 1/4" larger overall than the designated scope size.

Unertl 1-1/2" cap sets

- Black finished steel

- Sold as the set only.

- Dimension shown is the thread outside diameter.

- $35.20 plus shipping.

Unertl 1-1/4" cap sets

- Black finished steel

- Sold as the set only.

- Dimension shown is the thread outside diameter.

- $33.00 plus shipping.

"Other" Unertl 1-1/4" cap sets

- Black finished steel

- Sold as the set only.

- Dimension shown is the thread outside diameter.

- These caps are for the "other" 1-1/4" scope, with 3 circumferential screws on the objective end, as pictured.

- $33.00 plus shipping.

Unertl 1-inch cap sets

- Black finished steel

- Sold as the set only.

- Dimension shown is the thread outside diameter.

- $33.00 plus shipping.

Unertl 2" and UltraVarmint objective caps

- Black finished steel

- These are the 24-pitch thread version, not the 48-pitch which is sometimes encountered (see adapter rings below)

- $44.00 plus shipping. Sold individually.

Unertl 2" and UltraVarmint adapter rings

- Black finished steel

- 24-pitch female, 48-pitch male, for the objective end

- (Apparently Unertl discovered, fairly early, that a 48-pitch lens cap of that large diameter was just a hideous thing to try to install without cross-threading...)

- $44.00 plus shipping. Sold individually.

Unertl UltraVarmint eyepiece caps

- Black finished steel.

- About 1.40" overall outside diameter.

- Dimension shown is the thread outside diameter.

- $23.10 plus shipping. Sold individually.

Unertl 2" eyepiece caps

- Black finished steel.

- For the 1" tube scopes - about 1-3/16" overall outside diameter.

- Dimension shown is the thread outside diameter.

- $19.80 plus shipping. Sold individually.

Unertl "dehorned" mount caps

- Available either black or clear anodized.

- $9.10 per pair, plus shipping.

Litschert 1-1/4" cap sets

- Black anodized aluminum.

- Sold as the set only.

- Dimension shown is the thread outside diameter.

- $33.00 plus shipping.

Litschert 1-1/2" cap sets

- Black anodized aluminum.

- Sold as the set only.

- Dimension shown is the thread outside diameter.

- $35.20 plus shipping.

Balvar cap sets

- Machined black Delrin.

- Sold as the set only.

- $46.20 per set plus shipping.

Scope Rings

- For 3/4" (pictured), 7/8", or 1" tube scopes with 1/8" top rib.  (Lyman / Unertl type scopes)

     - Both 1/8" and 3mm top rib plungers are provided.

- Close re-creation of a less-common but desirable Unertl variant.

- 1/4-minute clicks.

- Clickless version also available. 

- Machined anodized aluminum and heat-treated black-finished steel.

- Non-rotating surfaces contacting the scope tube.

- Retained Delrin spring plungers.

- Fits standard-type scope blocks.  (Posa version may be forthcoming)

- Black or white/silver (clear anodized, email for availability) available.

3/4" set - $525.80. 7/8" set - $550.00. 1" set - $572.00.
Prices plus shipping.

Please note - because of design, manufacturing and tolerance differences,

parts for these rings will NOT necessarily fit the original Unertl rings.

Balvar Scope Rings -

- Love your B&L Balvar scope but hate the rear ring?  Here's the answer!

- Machined anodized aluminum and heat-treated black-finished steel.

- Non-rotating surfaces contacting the scope tube.

- Retained Delrin spring plunger.  Torlon pads on micrometer plungers.

- Fits standard-type scope blocks.  (Posa version is in the works)

- Front rings (not yet pictured) are also in stock.

Ring set - $572.00. Rear ring only - $471.90. Prices plus shipping.